เครื่องคิดเลข EPA แห่งชาติ Stormwater
เป็นเครื่องมือใหม่บนพื้นฐานของ SWMM ที่อาจจะเป็นที่สนใจนี
Hi
Does anyone know, if SWMM5 plots stacked on top of one another (like in GIRONÁS et al., 2009, p. 132), automatically, or one must do it manually?
Thanks in advance.
Valter Albino.
Read more…I only want to analyze the stormwater runoff reduction with LID, so in my case there is no any grey infrastructure. I used real rainfall and climate data for rain gage and climatology files, so I'm a little bit confused which kind of data I should pu
Read more…Pittsburgh was once described as Hell with the lid off. Well, whoever said that was an idiot.posted on August 3, 2013 at 12:28pm EDT
I have another question now. I'm only interested in LID control and the topic of my these is analyzing stormwater reduction with urban green infrastructure. Is it possible that I only simulate LID without considering grey infrastructure such as pipe,
Read more…I want to use 3-hour rainfall data from 12-01-2002 to 05-31-2010 for my rain gage, but every time I ran the model, it always appears error 321 no data in rainfall interface file for gage or error 319 invalid format for rainfall interface file. How c
Read more…I have the Galgary rainfall data 1 hour and 24 hour intensity at 5min intervals for 1y to 100y. How can I input it into SWMM gauge information? Please help! Thanks!And I am trying to model a retention ditch in the model, how to control the ditch to b
Read more…hi guys
I am a new user of SWMM 5
i am using it for my thesis on urban flooding. Can you help me explain these terms:
- ponded depth : is this the depth of surface water from the rim elevation. in my model, if a node is flooded, then this number equals
Read more…Under Kinematic wave routing, I want to know how the node ponding option control the flow of the system. What are the equations and what are the parameters govern the behavior of the ponded water when re introduce to the stream network? Is it just a
Read more…Canada Day and a SWMM 5 Model with Flow Dividers
Happy Canada Day, A SWMM 5 Model with Canada Day as the WaterMark along with an Interesting SWMM 5 Model with Flow Dividers - it only works in Kinematic Wave Mode
Read more…I 'm looking for a simple example with a solution in which rainwater flows from the network to the tank, and when it is full outflow to the receiver(river). The tank's max depth has to have 1 m depth. My point is a simple example with two or three
Read more…I need a clarification about the SWMM5.0 ' Runoff ' and the ' Outflow' in the results Table.
When I do not have a ground water compartment, I observed that Runoff results time series and the Outflow results time series had nearly similar values. I th
Read more…Is that SWMM is a Black Box model ? Can I change the parameters of runoff generation functions of the model to convert the model for regional watershed modelling. I mean when compare with the urban catchment modelling, rural catchments are more pe
Read more…I have develop a event based model to analyze the sensitivity of the channel parameters (Bed and Bank Roughness coefficient, Bed width, Maximum Depth) and the sensitivity of the intermittent storage areas. According to the results, sensitivity values
Read more…I would like to run simulations in SWMM on a given network to check the sensitivity analysis for TSS (pollutant). From what i have been able to figure out, I need to generate random numbers through standard functions and normal distributions for the
Read more…I used simple schematic to check the mass balance of the model. When I change the channel bed width, outflow hydro-graph peak was reduced but no time lag of the peak. I have found there is a system loss by internal outflow and due to that, I couldn
Read more…I have this rainfall data (see attached) that is not recognized by SWMM. Any ideas? Thanks
Read more…
Hi
Which formula of calculation of SWMM use Entry loss Coefficient , exit coefficient and Avg. loss coeff
Thank u
Read more…